The Cluster Receiver object
Table of Contents
Introduction
The receiver component is responsible for receiving cluster messages.
As you might notice through the configuration, is that the receiving of messages
and sending of messages are two different components, this is different from many other
frameworks, but there is a good reason for it, to decouple the logic for how messages are
sent from
how messages are received.
The receiver is very much like the Tomcat Connector, its the base of the thread pool
for incoming cluster messages. The receiver is straight forward, but all the socket settings
for incoming traffic are managed here.
Blocking vs Non-Blocking Receiver
The receiver supports both a non blocking, org.apache.catalina.tribes.transport.nio.NioReceiver,
and a
blocking, org.apache.catalina.tribes.transport.bio.BioReceiver. It is preferred
to use the non blocking receiver
to be able to grow your cluster without running into thread starvation.
Using the non blocking receiver allows you to with a very limited thread count to serve a
large number of messages.
Usually the rule is to use 1 thread per node in the cluster for small clusters, and then
depending on your message frequency
and your hardware, you'll find an optimal number of threads peak out at a certain number.
Attributes
Common Attributes
| Attribute | Description |
|---|---|
className |
The implementation of the receiver component. Two implementations available,
org.apache.catalina.tribes.transport.nio.NioReceiver and
org.apache.catalina.tribes.transport.bio.BioReceiver.The org.apache.catalina.tribes.transport.nio.NioReceiver is the
preferred implementation
|
address |
The address (network interface) to listen for incoming traffic.
Same as the bind address. The default value is auto and
translates to
java.net.InetAddress.getLocalHost().getHostAddress().
|
direct |
Possible values are true or false.
Set to true if you want the receiver to use direct bytebuffers when reading
data
from the sockets.
|
port |
The listen port for incoming data. The default value is 4000.
To avoid port conflicts the receiver will automatically bind to a free port
within the range of
port <= bindPort < port+autoBind
So for example, if port is 4000, and autoBind is set to 10, then the
receiver will open up
a server socket on the first available port in the range 4000-4009.
|
autoBind |
Default value is 100.
Use this value if you wish to automatically avoid port conflicts the cluster
receiver will try to open a
server socket on the port attribute port, and then work up
autoBind number of times.
|
securePort |
The secure listen port. This port is SSL enabled. If this attribute is omitted no SSL port is opened up. There default value is unset, meaning there is no SSL socket available. |
udpPort |
The UDP listen port. If this attribute is omitted no UDP port is opened up. There default value is unset, meaning there is no UDP listener available. |
selectorTimeout |
The value in milliseconds for the polling timeout in the
NioReceiver. On older versions of the JDK
there have been bugs, that should all now be cleared out where the selector
never woke up.
The default value is a very high 5000 milliseconds.
|
maxThreads |
The maximum number of threads in the receiver thread pool. The default value
is 6
Adjust this value relative to the number of nodes in the cluster, the number
of messages being exchanged and
the hardware you are running on. A higher value doesn't mean more
efficiency, tune this value according to your
own test results.
|
minThreads |
Minimum number of threads to be created when the receiver is started up.
Default value is 6
|
maxIdleTime |
Maximum number of milliseconds of until Idle thread terminates. Default
value is 60000 milliseconds.
|
ooBInline |
Boolean value for the socket OOBINLINE option. Possible values are true
or false.
|
rxBufSize |
The receiver buffer size on the receiving sockets. Value is in bytes, the
default value is 43800 bytes.
|
txBufSize |
The sending buffer size on the receiving sockets. Value is in bytes, the
default value is 25188 bytes.
|
udpRxBufSize |
The receive buffer size on the datagram socket.
Default value is 25188 bytes.
|
udpTxBufSize |
The send buffer size on the datagram socket.
Default value is 43800 bytes.
|
soKeepAlive |
Boolean value for the socket SO_KEEPALIVE option. Possible values are true
or false.
|
soLingerOn |
Boolean value to determine whether to use the SO_LINGER socket option.
Possible values are true or false. Default value
is true.
|
soLingerTime |
Sets the SO_LINGER socket option time value. The value is in seconds.
The default value is 3 seconds.
|
soReuseAddress |
Boolean value for the socket SO_REUSEADDR option. Possible values are true
or false.
|
tcpNoDelay |
Boolean value for the socket TCP_NODELAY option. Possible values are true
or false.
The default value is true
|
timeout |
Sets the SO_TIMEOUT option on the socket. The value is in milliseconds and
the default value is 3000
milliseconds.
|
useBufferPool |
Boolean value whether to use a shared buffer pool of cached org.apache.catalina.tribes.io.XByteBuffer
objects. If set to true, the XByteBuffer that is used to pass a message up
the channel, will be recycled at the end
of the requests. This means that interceptors in the channel must not
maintain a reference to the object
after the org.apache.catalina.tribes.ChannelInterceptor#messageReceived
method has exited.
|